Supported ProtectToolkit 7 platforms
The supported platforms for each version of ProtectToolkit 7 are listed below.
C=ProtectToolkit-C, PKCS#11 v2.10/2.20
M=ProtectToolkit-M, MS CSP 2.0 with CNG
J=ProtectToolkit-J, Java 7.x/8.x/9.x/10.x/11.x/17.x/21.x.
Note
Java 17.x and 21.x are only supported when using ProtectToolkit 7.2.3 or newer.
Note
The ProtectServer 3 HSM transitioned from FIPS 140-2 Level 3 to FIPS 140-3 Level 3 compliance and validation with the release of ProtectServer 3 HSM Firmware 7.03.01 (validation pending). The information in this section is grouped by the FIPS compliance and validation requirements that are relevant to your ProtectServer 3 HSM deployment.
Supported ProtectToolkit 7 platforms for FIPS 140-2 Level 3 deployments
This section lists the platforms supported by the following ProtectToolkit 7 versions, which are intended for FIPS 140-2 Level 3 deployments:
ProtectToolkit 7.2.3
ProtectToolkit 7.2.3 supports the platforms shown below.
| Windows version | OS type | 64-bit PTK component | 32-bit PTK component | PTK supported hardware |
|---|---|---|---|---|
| 11 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| 10 | 64-bit | C/M/J | C/J | PCIe31, PSE3, PSE3+ |
| Server 2022 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| Server 2019 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| Server 2016 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| Server 2012 R2 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
1 To deploy a ProtectServer 3 HSM with the 32-bit version of ProtectToolkit in PCI mode while using a 64-bit Windows 10 PC as the HSM and application host, you must follow the instructions described in Package installation sequence for 32-bit ProtectToolkit in PCI mode.
For Windows installation procedures, refer to Installing ProtectToolkit 7 on Windows.
| Linux version | OS type | 64-bit PTK component | 32-bit PTK component | PTK supported hardware |
|---|---|---|---|---|
| RHEL 9.1, 9.2 | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
| RHEL 8.4, 8.6, 8.7 | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
| RHEL 7.7, 7.9 | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
| SLES 12 SP5 | 64-bit | C/J | N/A | PSE3, PSE3+ |
| Ubuntu 20.04 LTS | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
For Linux installation procedures, refer to the following pages:
Note
If you are installing a patch version of ProtectToolkit on an AIX system, first install the initial release of the matching minor version of ProtectToolkit.
| AIX version | OS type | 64-bit PTK component | 32-bit PTK component | PTK supported hardware |
|---|---|---|---|---|
| 7.3 | 64-bit | C | C | PSE3, PSE3+ |
| 7.2 | 64-bit | C | C | PSE3, PSE3+ |
| 7.1 | 64-bit | C | C | PSE3, PSE3+ |
For AIX installation procedures, refer to
ProtectToolkit 7.2.1
ProtectToolkit 7.2.1 supports the platforms shown below.
| Windows version | OS type | 64-bit PTK component | 32-bit PTK component | PTK supported hardware |
|---|---|---|---|---|
| 11 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| 10 | 64-bit | C/M/J | C/J | PCIe31, PSE3, PSE3+ |
| Server 2022 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| Server 2019 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| Server 2016 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| Server 2012 R2 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
1 To deploy a ProtectServer 3 HSM with the 32-bit version of ProtectToolkit in PCI mode while using a 64-bit Windows 10 PC as the HSM and application host, you must follow the instructions described in Package installation sequence for 32-bit ProtectToolkit in PCI mode.
For Windows installation procedures, refer to Installing ProtectToolkit 7 on Windows.
| Linux version | OS type | 64-bit PTK component | 32-bit PTK component | PTK supported hardware |
|---|---|---|---|---|
| RHEL 9.1 | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
| RHEL 8.4, 8.6, 8.7 | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
| RHEL 7.7 | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
| SLES 12 SP5 | 64-bit | C/J | N/A | PSE3, PSE3+ |
| Ubuntu 20.04 LTS | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
For Linux installation procedures, refer to the following pages:
Note
If you are installing a patch version of ProtectToolkit on an AIX system, first install the initial release of the matching minor version of ProtectToolkit.
| AIX version | OS type | 64-bit PTK component | 32-bit PTK component | PTK supported hardware |
|---|---|---|---|---|
| 7.3 | 64-bit | C | C | PSE3, PSE3+ |
| 7.2 | 64-bit | C | C | PSE3, PSE3+ |
| 7.1 | 64-bit | C | C | PSE3, PSE3+ |
For AIX installation procedures, refer to
ProtectToolkit 7.2.0
ProtectToolkit 7.2.0 supports the platforms shown below.
| Windows version | OS type | 64-bit PTK component | 32-bit PTK component | PTK supported hardware |
|---|---|---|---|---|
| 11 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| 10 | 64-bit | C/M/J | C/J | PCIe31, PSE3, PSE3+ |
| Server 2019 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| Server 2016 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| Server 2012 R2 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
1 To deploy a ProtectServer 3 HSM with the 32-bit version of ProtectToolkit in PCI mode while using a 64-bit Windows 10 PC as the HSM and application host, you must follow the instructions described in Package installation sequence for 32-bit ProtectToolkit in PCI mode.
For Windows installation procedures, refer to Installing ProtectToolkit 7 on Windows.
| Linux version | OS type | 64-bit PTK component | 32-bit PTK component | PTK supported hardware |
|---|---|---|---|---|
| RHEL 8.4 | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
| RHEL 7.7 | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
| Ubuntu 20.04 LTS | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
For Linux installation procedures, refer to the following pages:
| AIX version | OS type | 64-bit PTK component | 32-bit PTK component | PTK supported hardware |
|---|---|---|---|---|
| 7.3 | 64-bit | C | C | PSE3, PSE3+ |
| 7.2 | 64-bit | C | C | PSE3, PSE3+ |
| 7.1 | 64-bit | C | C | PSE3, PSE3+ |
For AIX installation procedures, refer to
ProtectToolkit 7.1.0
ProtectToolkit 7.1.0 supports the platforms shown below.
| Windows version | OS type | PTK component | PTK supported hardware |
|---|---|---|---|
| 10 | 64-bit | C/M/J | PCIe3, PSE3, PSE3+ |
| Server 2019 | 64-bit | C/M/J | PCIe3, PSE3, PSE3+ |
| Server 2016 | 64-bit | C/M/J | PCIe3, PSE3, PSE3+ |
| Server 2012 R2 | 64-bit | C/M/J | PCIe3, PSE3, PSE3+ |
For Windows installation procedures, refer to Installing ProtectToolkit 7 on Windows.
| Linux version | OS type | PTK component | PTK supported hardware |
|---|---|---|---|
| RHEL 8.4 | 64-bit | C/J | PCIe3, PSE3, PSE3+ |
| RHEL 7.7 | 64-bit | C/J | PCIe3, PSE3, PSE3+ |
| Ubuntu 20.04 LTS | 64-bit | C/J | PCIe3, PSE3, PSE3+ |
For Linux installation procedures, refer to the following pages:
ProtectToolkit 7.0.0
ProtectToolkit 7.0.0 supports the platforms shown below.
| Windows version | OS type | PTK component | PTK supported hardware |
|---|---|---|---|
| 10 | 64-bit | C/M/J | PCIe3, PSE3, PSE3+ |
| Server 2019 | 64-bit | C/M/J | PCIe3, PSE3, PSE3+ |
| Server 2016 | 64-bit | C/M/J | PCIe3, PSE3, PSE3+ |
| Server 2012 R2 | 64-bit | C/M/J | PCIe3, PSE3, PSE3+ |
For Windows installation procedures, refer to Installing ProtectToolkit 7 on Windows.
| Linux version | OS type | PTK component | PTK supported hardware |
|---|---|---|---|
| RHEL 7.7 | 64-bit | C/J | PCIe3, PSE3, PSE3+ |
For Linux installation procedures, refer to the following pages:
Supported ProtectToolkit 7 platforms for FIPS 140-3 Level 3 deployments
This section lists the platforms supported by the following ProtectToolkit 7 versions, which are intended for FIPS 140-3 Level 3 deployments:
Note
If you are reconfiguring a ProtectServer 3 HSM deployment for FIPS 140-3 Level 3-compliance, read Firmware 7.03.01 advisory notes to take note of the operational changes that this firmware version introduces and reconfigure applications where necessary, before reconfiguring the deployment for 140-3 Level 3-compliance.
ProtectToolkit 7.3.1
ProtectToolkit 7.3.1 supports the platforms shown below.
| Windows version | OS type | 64-bit PTK component | 32-bit PTK component | PTK supported hardware |
|---|---|---|---|---|
| 11 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| 10 | 64-bit | C/M/J | C/J | PCIe31, PSE3, PSE3+ |
| Server 2022 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| Server 2019 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| Server 2016 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| Server 2012 R2 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
1 To deploy a ProtectServer 3 HSM with the 32-bit version of ProtectToolkit in PCI mode while using a 64-bit Windows 10 PC as the HSM and application host, you must follow the instructions described in Package installation sequence for 32-bit ProtectToolkit in PCI mode.
For Windows installation procedures, refer to Installing ProtectToolkit 7 on Windows.
| Linux version | OS type | 64-bit PTK component | 32-bit PTK component | PTK supported hardware |
|---|---|---|---|---|
| RHEL 9.1, 9.2, 9.3 | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
| RHEL 8.4, 8.6, 8.7, 8.9, 8.10 | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
| RHEL 7.7, 7.9 | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
| SLES 15 SP4 | 64-bit | C/J | N/A | PSE3, PSE3+ |
| SLES 12 SP5 | 64-bit | C/J | N/A | PSE3, PSE3+ |
| Ubuntu 20.04, 22.04.4 LTS | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
For Linux installation procedures, refer to the following pages:
| AIX version | OS type | 64-bit PTK component | 32-bit PTK component | PTK supported hardware |
|---|---|---|---|---|
| 7.3 | 64-bit | C | C | PSE3, PSE3+ |
| 7.2 | 64-bit | C | C | PSE3, PSE3+ |
| 7.1 | 64-bit | C | C | PSE3, PSE3+ |
For AIX installation procedures, refer to
Note
If you are reconfiguring a ProtectServer 3 HSM deployment for FIPS 140-3 Level 3-compliance, read Firmware 7.03.00 advisory notes to take note of the operational changes that this firmware version introduces and reconfigure applications where necessary, before reconfiguring the deployment for 140-3 Level 3-compliance.
ProtectToolkit 7.3.0
ProtectToolkit 7.3.0 supports the platforms shown below.
| Windows version | OS type | 64-bit PTK component | 32-bit PTK component | PTK supported hardware |
|---|---|---|---|---|
| 11 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| 10 | 64-bit | C/M/J | C/J | PCIe31, PSE3, PSE3+ |
| Server 2022 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| Server 2019 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| Server 2016 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
| Server 2012 R2 | 64-bit | C/M/J | N/A | PCIe3, PSE3, PSE3+ |
1 To deploy a ProtectServer 3 HSM with the 32-bit version of ProtectToolkit in PCI mode while using a 64-bit Windows 10 PC as the HSM and application host, you must follow the instructions described in Package installation sequence for 32-bit ProtectToolkit in PCI mode.
For Windows installation procedures, refer to Installing ProtectToolkit 7 on Windows.
| Linux version | OS type | 64-bit PTK component | 32-bit PTK component | PTK supported hardware |
|---|---|---|---|---|
| RHEL 9.1 | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
| RHEL 8.4, 8.6, 8.7 | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
| RHEL 7.7 | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
| SLES 15 SP4 | 64-bit | C/J | N/A | PSE3, PSE3+ |
| SLES 12 SP5 | 64-bit | C/J | N/A | PSE3, PSE3+ |
| Ubuntu 20.04 LTS | 64-bit | C/J | N/A | PCIe3, PSE3, PSE3+ |
For Linux installation procedures, refer to the following pages:
| AIX version | OS type | 64-bit PTK component | 32-bit PTK component | PTK supported hardware |
|---|---|---|---|---|
| 7.3 | 64-bit | C | C | PSE3, PSE3+ |
| 7.2 | 64-bit | C | C | PSE3, PSE3+ |
| 7.1 | 64-bit | C | C | PSE3, PSE3+ |
For AIX installation procedures, refer to
